Attach An Awning Ledger Board To A Wood Siding House

Stratton Bracket Advantages In 2020 Building A Deck Deck With Pergola Diy Deck

Stratton Bracket Advantages In 2020 Building A Deck Deck With Pergola Diy Deck

How To Attach Pergola To House Google Search Attached Pergola Pergola Canopy Wooden Pergola

How To Attach Pergola To House Google Search Attached Pergola Pergola Canopy Wooden Pergola

Fastening A Patio Roof To The House Hometips Building A Patio Pergola Attached To House Building A Deck

Fastening A Patio Roof To The House Hometips Building A Patio Pergola Attached To House Building A Deck

Ledger Board Attachment To Brick Siding Building A Deck Brick Siding Diy Deck

Ledger Board Attachment To Brick Siding Building A Deck Brick Siding Diy Deck

Inspecting A Deck Illustrated Masonry Wall Masonry Building A Deck

Inspecting A Deck Illustrated Masonry Wall Masonry Building A Deck

How To Install A Ledger Building A Deck Diy Deck Deck Construction

How To Install A Ledger Building A Deck Diy Deck Deck Construction

How To Install A Ledger Building A Deck Diy Deck Deck Construction

If you have beveled horizontal siding then use an inverted piece of siding as shown in the illustration here to create a plumb flat surface for attaching the ledger.

Attach an awning ledger board to a wood siding house.

Make it the full width of the porch or slightly wider depending on your porch design. If necessary use a sliding bevel to determine angles needed where the rafters will meet the ledger board. Find the wall studs or roof trusses that will have to support the ledger. Anchor deck joists to the ledger with joist hangers filling each hole with galvanized joist hanger nails rated for pressure treated wood.

This is the only way to ensure the connection is water tight. Determine how high it must be to provide an adequate slope to the roof. Locate a position for a header or ledger board. The screws should penetrate the ledger the sheathing the house and go into a framing beam such as a floor joist or a wall stud.

Attach 2x6 rafters to the house with joist hangers and or supported by the ledger board. Attaching a deck ledger securely is only half the work of installing a ledger. So make a mark above 7 to 8 inches and keep a minimum gap of 2 inches at one of the ends. Also you need to keep enough open space approximately 3 4 inches above the top of the mounting bracket and ledger board.

In order to install the ledger board you usually need to remove the house s siding. Dia galvanized or stainless steel lag screws in every other joist space alternating up and down positions to keep the ledger from splitting. Rafters are placed on 24 centers and attached to the beams and settle joists are attached as needed image 1. Once the ledger board is tightly fastened into place use a caulk gun to caulk all the seams between the ledger and the house with weatherproof caulk.

A ledger relies on the fasteners and strength of the wood ledger board and rim board of the house to carry the deck live and dead loads. Most house framing relies on building elements floors walls roofs being stacked one atop another. The awning should be at least 7 to 8 feet above the ground or the patio. If your siding is not beveled you can simply screw the ledger tightly to it.

Attaching Ledger Board Pergola Pergola Kits Replacement Canopy

Attaching Ledger Board Pergola Pergola Kits Replacement Canopy

Attachingaledgertobrick Gif 382 322 Pixels In 2020 Building A Deck Exterior Brick Brick Wall

Attachingaledgertobrick Gif 382 322 Pixels In 2020 Building A Deck Exterior Brick Brick Wall

Corrugated Patio Cover Note This Is Not Attached To The House The Pergola Patio Covered Patio Building A Deck

Corrugated Patio Cover Note This Is Not Attached To The House The Pergola Patio Covered Patio Building A Deck

Pin By Wendy Haston On Porch Building A Deck Timber Deck Deck Framing

Pin By Wendy Haston On Porch Building A Deck Timber Deck Deck Framing

Source : pinterest.com